C.A. Technologies Techline T3

Inside This Document

The nozzle/needle chart and parts sheet for the C.A. Technologies Techline T3 spray gun. Orifice sizes run 1.3 mm through 2.2 mm (33-0213 to 33-0222 tips with 40-P13xx needles) on matched 23-10xx air caps at 45 PSI maximum gun inlet pressure for HVLP operation. The larger-tip range and higher inlet ceiling point the Techline T3 at primers, high-build coatings, and heavier-bodied industrial materials.

From the Document

Orifice Size Air Cap Max Gun Inlet Pressure for HVLP Orifice (Tip) Needle 1.3 23-1013 45 33-0213 40-P1313 1.4 23-1014 45 33-0214 40-P1314 1.5 23-1015 45 33-0215 40-P1315 1.7 23-1017 45 33-0217 40-P1317 1.9 23-1019 45 33-0219 40-P1319 2.2 23-1022 45 33-0222 40-P1322 NOZZLE NEEDLE CHART Part Number Description Part Number Description 1 60-1130 Body Assembly 6 See Below Needle 2 33-1201 Nozzle Body 7 T21 Needle Return Spring 3 See Below Orifice 8 T25 Fluid Control Knob 4 See Below Air Cap 5 T27 Packing 9 10-111 Tool Kit: Gun wrench, filter, needle packing wrench and brush „™2 „Q €—2ƒ I P W R S U V T IH BxX h2 2   2 2 2™—  2  2 2@5IHA „2 2—™ 2 2 2 — —2—   2— 2 2˜2 2 ™—"22— 2—F2…22—™ 2%  ™ 2 2IHEIII2F Be 2g—22—2— 2— ——˜22™  2r†v€2™ — ™F HVLP Kits Orifice Size Air Cap Orifice (Tip) Needle TK 1010 1.0 23-1010 33-0210 40-P1310 TK 1013 1.3 23-1013 33-0213 40-P1313 TK 1014 1.4 23-1014 33-0214 40-P1314 TK 1015 1.5 23-1015 33-0215 40-P1315 TK 1017 1.7 23-1017 33-0217 40-P1317 TK 1019 1.9 23-1019 33-0219 40-P1319 TK 1022 2.2 23-1022 33-0222 40-P1322 Kits For Techline HVLP Gravity Gun Material Orifice Size T3 HVLP Filler 1.7 45 PSI @ 13.5 CFM Primer, Washprimer, Epoxy 1.4 - 1.7 45 PSI @ 13.5 CFM Sealer 1.4 - 1.7 45 PSI @ 13.5 CFM Single Stage 1.3 - 1.4 45 PSI @ 13.5 CFM Basecoat 1.3 - 1.4 45 PSI @ 13.5 CFM Clearcoat 1.3 - 1.4 45 PSI @ 13.5 CFM High Solids Clears 1.4 - 1.5 45 PSI @ 13.5 CFM Techline Nozzle Selection Chart y) —2—2w— —™…